Showing results: 976 - 990 of 1308 items found.
-
EL3630B -
MCH Instruments Co.,Ltd.
Features:*Number operation and control*LED display with high definition and high contrast, rich display information*Easy operation of knob encoder switch*Basic load function: constant current, voltage, power and resistance*Multi units used to multiple load ability*Short-circuit test*Battery test*Dynamic test*Multi parameters measured in the list*Remote voltage measurement*Panel and exterior trigger function*Protection function: over-voltage, over-current, over-power, over-heat, polarity connection in reverse*10 sets of parameters memorized and loaded, and automatically loaded on turning on the instrument*Intelligent fan control*Key lock and knob lock functions
-
LX-221A+ -
Shenzhen Lian Xin Technology Co., Ltd.
·Meet UL, VDE, CSA, SAA, T-MARK, KS. IRAM, CCC and other countries’ standards .·Used to test single – ends ,double –ends ,three-ends power supply cords.·Auto and continuous test in COND,Insulation Resistance ,Leakage Current, Line-to-line Hi-pot(inside HV), Leaking copper(outside HV), relative length,·Auto test the fine and detective goods, tested qualified ones can be be ejected by ejector pin and marked , automatic cutting defective products， and alarmed with voice prompt and light,·Provide with RS 232 interfaces, can communicate with PC, easy to upgrade,·Provide personalized customization according to different requirements.
-
NX5730A -
Keysight Technologies
Precise and fast characterization of new memory, such as spin transfer torque magneto resistive random access memory (STT-MRAM) from DC to high-speed pulsed IV measurement on silicon wafers Apply accurate and high-speed pulsed voltages (down to 1 ns pulse) to magnetic tunnel junction (MTJ) for STT-MRAM and precisely measure the resistance of MTJ Perform all typical MTJ characterization tests in one solution10 to 100 times faster cycle test, such as a bit error rate test (BERT)Capture and visualize MTJ switching waveforms clearly during the writing pulse Dedicated solution with Keysight Technologies’ technical expertise
-
TOS5300 Series -
Kikusui Electronics Corp.
The "TOS5300 Series" is a series of test instruments used in Hipot (withstanding voltage) tests and insulation resistance tests, two of the four tests regarded as necessary for ensuring the safety of electrical products. With an output of 5 kV/100 mA (AC) and 6 kV/10 mA (DC), the series can be used in Hipot (withstanding voltage) & insulation resistance testing of electronic equipment and electronic parts, based on the requirements of IEC, EN, UL, VDE, JIS, and other international safety standards and the Electrical Appliance and Material Safety Law. Also, the test voltage stability is improved with the adoption of a newly developed switching amplifier. Since the output voltage can be kept constant even when the AC line voltage or frequency changes, consistent testing can be performed, even when the power supply environment is in an unstable region. The TOS5300 is also equipped with a number of features that are capable of meeting a variety of test needs. It is a new low-cost standard model that provides thorough operability, reliability and safety.
-
IBEKO Power AB
Contact resistance measurement is one of the most important and common tests during switchgear manufacturing, commissioning and maintenance stages. Besides switchgear testing, the RMO digital micro-ohmmeters are designed for simple, safe and efficient testing of:disconnecting switches,high-current bus bar joints,cable splices,welding joints,and different high-current links in factory and high-induction field environments.All DV Power RMO micro-ohmmeters use Kelvin’s 4-point measurement principle which is the most convenient for very small resistance measurements. The measurements are accurate and in accordance with international standards for AC high-voltage circuit breakers testing (IEEE C37.09 and IEC 62271-100).Starting from 2003, DV Power has been a trend-setter on the market when our first 500 A micro-ohmmeter weighing only 8 kg (RMO500A / CPM500) was released.Currently, DV Power products portfolio includes 16 models, divided into 3 series:13 portable models: RMO-A (6) and RMO-G (7) series.6 handheld models: RMO-H (6) seriesThe instruments generate a user-selectable and ripple-free test current up to 800 A in an automatically regulated test ramp. Test current ramping significantly decreases the influence of the magnetic transients to measurement.
-
Shanghai Linpin Instrument
Single-wing Drop Test Machine Simulate the drop conditions of packaged products when different faces, edges and corners fall to the ground from different heights, thus to understand the damage of the product and evaluate the drop height and impact resistance that the packaging materials can endure while falling down, so as to improve and optimize package design according to actual conditions of the product and national standard range.
-
National Technical Systems
Compression testing is a very common testing method that is used to establish the compressive force or crush resistance of a material and the ability of the material to recover after a specified compressive force is applied and even held over a defined period of time. Compression tests are used to determine the material behavior under a load. The maximum stress a material can sustain over a period under a load (constant or progressive) is determined.
-
Chroma Systems Solutions, Inc.
The Chroma 16502 Milliohm Meter is Chroma’s newest digital Milliohm Meter. 0.001mΩ~1.9999MΩ wide measurement range. DC, Pulsed, and Dry-circuit test current driving modes, enable the Chroma 16502 can be properly used in DC resistance measurement for various inductive components (coil, choke, and transformer winding etc.), cable, metallic contact (connector, relay switch etc.) and conduction materials.
-
Extech MA3110 -
Extech Instruments Corporation
Flexible 11" (28cm) clamp jaw easily wraps around bus bars and cable bundles that may be difficult to access with regular clamp meters. The thin 8mm cable diameter easily fits into tight spaces. Includes test leads for multimeter functions measuring Voltage, Resistance, and Capacitance. True RMS and CAT IV rated allows for maximum accuracy and safety for your measurements.
-
Applied Relay Testing Ltd.
A connector test system which provides expansion of up to 160 Kelvin pair connections. The system incorporates high voltage AC and DC power supplies with a maximum output of +/- 2100 Volts peak for Hi Pot, Insulation resistance measurement. LCR bridge control is provided with 4 terminal multiplexing in order to add precision capacitance, inductance and resistance measurement capability. An integral H.V. capacitor bias option permits capacitance measurement to be made at up to 2.1kV.
-
Extech MN35 -
Extech Instruments Corporation
The MN35 is a convenient mini size multimeter with protective rubber holster and tilt stand. Manual ranging, measures AC and DC Voltage to 600V, Resistance with Continuity and Diode functions, DC Current to 10A, Temperature, and 9V/1.5V Battery test. Includes protective rubber holster, 9V battery, test leads and Type K thermocouple probe.
-
Gill AC -
ACM Instruments
ACM's flagship instrument offers a Potentiostat, Galvanostat and Zero Resistance Ammeter with integrated Frequency Response Analyser and Sweep Generator in one.Electrochemical tests such as AC Impedance (EIS) and standard DC tests including LPR and current and voltage noise are included, making this instrument extremely versatile and great value for money.To better meet your specific needs why not customise your instrument with our options, so versatile are our instruments that many options are even available to be fitted retrospectively, making our instruments the right choice now and for the long term.
-
Dongguan Amade Instruments Technology Co., Ltd
Ozone aging test chamber is also called as ozone climate simulator or ozone aging tester. It is one of climatic testing instruments, which is to simulate and intensify the ozone condition for determining the cracking resistance of vulcanized or thermoplastic rubbers when subjected to dynamic or static tensile strain exposed at a man-made constant temperature to atmosphere containing given concentration of ozone in conformance with relevant specification. Ozone test is an indispensable method for people to research effects and mechanisms of ozone on rubbers, quick identify and evaluate anti-aging performance of rubbers and find solutions for improvement of quality and lifespan.
-
PPTM01AS -
Matco Tools
*Connects with the new Power Probe Tek application for greater diagnostic functionality*The Maestro and Power Probe Tek App will be compatible to connect with a majority of diagnostic scan tools*Trace mode offers scope-like functionality*Stream and record visual traces of electrical issues found when diagnosing*DC voltmeter with the capability of applying battery supplied voltage or ground*AC voltmeter: TRMS, peak-to-peak/min/max, frequency, duty cycle*Resistance testing with a live or unloaded circuit*Fuel-injector test mode*Driver test for testing module drivers
-
783129-01 -
NI
PXIe, 6½-Digit, ±300 V, Onboard 1.8 MS/s Isolated Digitizer, PXI Digital Multimeter—The PXIe‑4080 is a high-performance 6½‑digit, 300 V DMM that provides the measurement capabilities found in two common test instruments: a high-resolution DMM and a digitizer. As a DMM, the PXIe‑4080 delivers fast, accurate AC/DC voltage, AC/DC current, 2‑ or 4‑wire resistance, and frequency/period measurements, as well as diode tests. In the high-voltage, isolated digitizer mode, the PXIe‑4080 can acquire waveforms at sample rates up to 1.8 MS/s.
